Simer 2803 Owner's Manual download pdf (Page 3)

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Installation 3

Pump water only with this pump.

Periodically inspect pump and system components.

Wear safety glasses at all times when working on

pumps.

Keep work area clean, uncluttered and properly lighted;

store properly all unused tools and equipment.

Keep visitors at a safe distance from the work areas.

Pump body may explode if used as a

booster pump unless relief valve capable of passing full

pump flow at 75 psi is installed.

SHALLOW WELL JET PUMP

INSTALLATIONS:

• Have a vertical depth between the pump and the

water being pumped of 25’ or less.

• Have one pipe from the well to the pump case.

• Can be installed in a bored or drilled well, or in a

driven well.

REPLACING AN OLD PUMP

Hazardous voltage. Disconnect power to

pump before working on a pump or a motor.

1. Drain and remove the old pump. Check the old pipe

for scale, lime, rust, etc., and replace it if necessary.

2. Install the pump in the system. Make sure that all

pipe joints in the suction pipe are air-tight as well as

water tight.

If the suction pipe can suck air, the

pump will not be able to pull water from the well.

3. Adjust the pump mounting height so that the

plumbing connections do not put a strain on the

pump body. Support the pipe so that the pump body

does not take the weight of piping or fittings.

You have just completed the well plumbing for your

new shallow well jet pump. Please go to Pages 5 and 6

for discharge pipe and tank connections.

WELL POINT (DRIVEN POINT)

INSTALLATION (FIGURE 1)

1. Drive the well, using drive couplings and a drive cap.

Drive fittings are threaded all the way through and

allow the pipe ends to butt against each other so that

the driving force of the maul is carried by the pipe

and not by the threads. The ordinary fittings found in

hardware stores are not threaded all the way through

the fitting and can collapse under impact. Drive

fittings are also smoother than standard plumbing

fittings, making ground penetration easier.

2. Mount the pump as close to the well as possible

3. Use the fewest possible fittings (especially elbows)

when connecting the pipe from the well point to the

pump suction port. The suction pipe should be at

least as large as the suction port on the pump

(include a check valve as close to the well as

possible - see Figure 1). Support the pipe so that

there are no dips or sags in the pipe, so it doesn’t

strain the pump body, and so that it slopes slightly

upward from the well to the pump (high spots can

cause air pockets which can air lock the pump). Seal

the suction pipe joints with teflon tape. Joints must

be air- and water-tight.

If the suction pipe can suck

air, the pump cannot pull water from the well.

one well point does not supply enough water,

consider connecting two or three well points to one

suction pipe.

You have just completed the suction piping for your

new shallow well jet pump. Please go to Pages 5 and 6

for discharge pipe and tank connections.

WARNING

Hazardous pressure!

Install pressure relief

valve in discharge pipe.

Release all pressure on

system before working on

any component.

Drive

Coupling

Drive

Point

Drive point

below water

level

Pump Priming Tee and Plug

(Replace plug with pressure

Gauge if desired – purchase

separately)

2346 0396 SIM

To Household

Water System

Suction Pipe

From Well

Check

Valve

Priming

Tee and

Plug

Not

Scale

Figure 1 – Driven Point Installation

1 2 3 4 5 6 7 8 ... 27 28

Comments to this Manuals

No comments

Simer 2803 Owner's Manual Page 3

Comments to this Manuals

Related products and manuals for Water pumps Simer 2803